|
If you can't view the Datasheet, Please click here to try to view without PDF Reader . |
|
Datasheet File OCR Text: |
aAM3104 ULTRA LOW POWER, 4-CHANNEL CMOS ANALOG MULTIPLEXER Preliminary Specification PRODUCT SPECIFICATION Pin Configuration - Subject to change without notice General Description The aAM3104 is a precision CMOS analog multiplexer offering low on-resistance of less than 4, with better than 0.4 matching between channels and extremely flat resistance over the specified analog input voltage range of less than 1.2.The aAM3104 has very fast enable switching speed of less than 20nS over the full operating temperature range of -40C to 85C. The aAM3104 also consumes a minimal amount of power, making them ideal for portable equipment. The aAM3104 connects 1-of-4 inputs to a common output by control of a 2-bit binary address. An enable pin disconnects all inputs from the output. The part is available in a 10-contact, leadless QFN package and operates over the range from 1.8V to 5.5V. A0 NO1 GND NO3 EN 1 2 3 10 9 8 A1 NO2 COM NO4 VDD aAM3104 4 5 7 6 Features (5V VDD) * * * * * * * * * Low On-Resistance: 4 Max Guaranteed On-resistance match between channels, < 0.4 Guaranteed Flat On-resistance over specified signal range, < 1.2. Enable Turn-On time: 14nS at 25C Enable Turn-Off time: 6nS at 25C Transition Time: 14nS at 25C Break before Make Interval: 8nS at 25C Temperature Range: -40C to 85C Uses a Single Supply: 3V to 5V nominal NO1 NO2 NO3 NO4 CMOS DECODERS / DRIVERS VDD GND Preliminary Specification Functional Diagram COM Applications * * * * * Mobile Communications Computers and Peripherals Battery Management FAX Machines/Printers/Copiers Portable Medical Instruments EN A0 A1 Ordering Information Part Number AAM3104Q10 Package 10-Lead QFN Temperature Range -40C to +85C Part Marking aAM3104 How Supplied 3000 units on T&R (c) Andigilog, Inc. 2004 www.andigilog.com August 2004 - 70A04011 Preliminary Specification - Subject to change without notice aAM3104 Absolute Maximum Ratings1 Parameter Supply Voltage Analog Input/Output Voltage Address/EN Input Voltage Continuous Current, any terminal Storage Temperature Range Lead Soldering Temperature ESD2 Human Body Model Machine Model Thermal Resistance - JA Rating +7V -0.5V to VDD + 0.5V -0.5V to VDD + 0.5V 50mA -60C to +150C 260C 2000V 250V TBD 3. 2. NOTES: 1. Absolute maximum ratings are limits beyond which operation may cause permanent damage to the device. These are stress ratings only; functional operations at or above these limits is not implied. Human Body Model: 100pF capacitor discharged through a 1.5k resistor into each pin. Machine Model: 200pF capacitor discharged directly into each pin. These specifications are guaranteed only for the test conditions listed. - Subject to change without notice Recommended Operating Ratings Symbol VDD VNO, VCOM TA Parameter Supply Voltage Analog Signal Level Operating Temperature Range Min +1.8 0 -40 Max +5.5 VDD +85 Units V V C DC Electrical Characteristics (Digital section)3 Limits apply for -40C T A +85C and V D D = + 5.0V unless otherwise noted. Parameter Min Hi-Level Input Voltage Max Low-Level Input Voltage Digital Input Leakage Symbol VIH VIL IIN Conditions -40C TA +85C -40C TA +85C VADD & VEN = 0V or +5.5V VDD = +5.5V VDD = +2.7V VDD = +4.5V VDD = +2.7V VDD = +4.5V TA= +25C TA = -40C to +85C Min 2.0V 2.4V Max Units V 0.4V 0.8V 0.1 1.0 V A Preliminary Specification -0.1 -1.0 DC Electrical Characteristics (Analog Section)3 Limits apply for -40C T A +85C and V D D = + 5.0V unless otherwise noted. Parameter ON-Resistance Symbol RON Conditions TA = +25C INO = -10mA VCOM = 0V to VDD TA = -40C to +85C TA = +25C VDD = +3V, INO = -10mA VCOM = 0V to VDD TA = -40C to +85C INO = -10MA, VDD = +4.5V TA = +25C VCOM = 0 to VDD TA = -40C to +85C INO = -10MA, VDD = +2.7V TA = +25C VCOM = 0 to VDD TA = -40C to +85C INO = -10mA, VDD = +5V TA = +25C VCOM = 0 to VDD TA = -40C to +85C INO = -10mA, VDD = +3V TA = +25C VCOM = 0 to VDD TA = -40C to +85C TA = +25C VDD = +3.3V or +5.5V, VADD & VEN = 0V or VDD TA = -40C to +85C Min Typ 2 4 7 0.1 0.4 0.1 0.4 0.75 1.2 1.2 3 0.1 1 Max 4 Units A ON-Resistance channel matching RON ON-Resistance Flatness Supply Current RFLAT IDD -2(c) Andigilog, Inc. 2004 www.andigilog.com August 2004 - 70A04011 Preliminary Specification - Subject to change without notice aAM3104 Dynamic Electrical Characteristics3 Limits apply for -40C T A +85C and V D D = + 5.0V unless otherwise noted. Parameter Symbol tTRANS Conditions TA = +25C VDD = +5V, VNO = 3V CL = 35pF, RL = 300 TA = -40C to +85C TA = +25C VDD = +3V, VNO = 2V CL = 35pF, RL = 300 TA = -40C to +85C TA = +25C VDD = +5V, VNO = 3V CL = 35pF, RL = 300 TA = -40C to +85C TA = +25C VDD = +3V, VNO = 2V CL = 35pF, RL = 300 TA = -40C to +85C TA = +25C VDD = +5V, VNO = 3V CL = 35pF, RL = 300 TA = -40C to +85C TA = +25C VDD = +3V, VNO = 2V CL = 35pF, RL = 300 TA = -40C to +85C TA = +25C VDD = +5V, VNO = 3V CL = 35pF, RL = 300 TA = -40C to +85C TA = +25C VDD = +3V, VNO = 2V CL = 35pF, RL = 300 TA = -40C to +85C f = 1MHz TA = +25C, f = 1MHz f = 1MHz; VEN = VNO = 0V TA = +25C, f = 1MHz VEN = +0.8V; VCOM = 0V VEN = +2.4V; VCOM = 0V TA = +25C, f = 1MHz TA= +25C, f = 1MHz Min Typ 12 17 24 3 1 3 1 10 20 13 24 7 13 10 16 8 8 50 60 ns pF pF pF pF ns ns ns Max 20 Units ns ns ns - Subject to change without notice Transition Time Break-BeforeMake Interval tOPEN Enable Turn-On Time tON(EN) Enable Turn-Off Time Logic Input Cap. NO-off-ch Cap. COM-Off-ch Cap. COM-On-ch Cap tOFF(EN) CIN CNO(OFF) CCOM(OFF) CCOM(ON) Test Circuits / Timing Diagrams Figure 1. Enable Switching Time VDD VEN VDD EN VIH tR = tF <5nS 50% 50% Preliminary Specification N01 VNO LOGIC INPUT VEN 0V VNO N02 - N04 aAM3104 50 A0 A1 COM GND VCOM 300 35pF MUX OUTPUT VCOM 90% 90% 0V tON tOFF Figure 2. Transition Time VDD VDD VIH tR = tF <5nS 50% 50% VADR EN N01, N03, N04 A0 N02 VNO LOGIC INPUT VADR 0V VNO aAM3104 GND 50 COM A1 VCOM 300 35pF MUX OUTPUT VCOM 90% 90% 0V tON tOFF -3(c) Andigilog, Inc. 2004 www.andigilog.com August 2004 - 70A04011 Preliminary Specification - Subject to change without notice aAM3104 Test Circuits / Timing Diagrams (Cont'd) Figure 3. Break-Before-Make Time VDD VIH tR = tF <5nS - Subject to change without notice VADR 50 VIH EN A0 A1 VDD N01 - N04 VADR 0V VDD VNO VCOM 300 35pF MUX OUTPUT VCOM aAM3104 COM GND 90% 90% 0V tOPEN Truth Table A1 X 0 0 1 1 A0 X 0 1 0 1 EN 0 1 1 1 1 ON Sw itch None 1 2 3 4 Preliminary Specification Logic "0" VIL 0.8V, Logic "1" 2.4V -4(c) Andigilog, Inc. 2004 www.andigilog.com August 2004 - 70A04011 Preliminary Specification - Subject to change without notice LOGIC INPUT 50% aAM3104 QFN-10 Package Dimensions Pin 1 Dot Marking 0.900 0.050 3.000 0.050 0.250 0.050 Pin 1 Identification R 0.200 TYP - Subject to change without notice 3.000 0.050 SLP / QFN 10L (3mm x 3mm) 0.250 0.050 2.000 REF 0.500 bsc 2.400 0.050 Exposed Pad 1.700 0.050 Exposed Pad 0.000 - 0.050 0.203 0.025 Top View Bottom View Side View Tape & Reel Dimensions 8.00 0.10 2.00 0.05 (Note 2.) 4.00 (Note 1.) A O 1.50 + 0.10 1.75 0.10 0.3 0.05 O 1.50 MIN 5.50 0.05 12.00 0.30 3.30 3.3 0.10 Preliminary Specification 3.30 1.1 SEC - AA A Notes: 1. 10 hole cumulative tol. 0.2 2. Measured to the true position of the pocket Part Orientation -5(c) Andigilog, Inc. 2004 www.andigilog.com August 2004 - 70A04011 Preliminary Specification - Subject to change without notice aAM3104 Data Sheet Classifications Preliminary Specification This classification is shown on the heading of each page of a specification for products that are either under development (design and qualification), or in the formative planning stages. Andigilog reserves the right to change or discontinue these products without notice. New Release Specification This classification is shown on the heading of the first page only of a specification for products that are either under the later stages of development (characterization and qualification), or in the early weeks of release to production. Andigilog reserves the right to change the specification and information for these products without notice. - Subject to change without notice Fully Released Specification Fully released datasheets do not contain any classification in the first page header. These documents contain specification on products that are in full production. Andigilog will not change any guaranteed limits without written notice to the customers. Obsolete datasheets that were written prior to January 1, 2001 without any header classification information should be considered as obsolete and non-active specifications, or in the best case as Preliminary Specifications. Preliminary Specification LIFE SUPPORT POLICY ANDIGILOG'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL COUNSEL OF ANDIGILOG, INC. As used herein: 1. Life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. A critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. Andigilog, Inc. 8380 S. Kyrene Rd., Suite 101 Tempe, Arizona 85284-2120 Tel: (480) 940-6200 Fax: (480) 940-4255 -6(c) Andigilog, Inc. 2004 www.andigilog.com August 2004 - 70A04013 Preliminary Specification - Subject to change without notice |
Price & Availability of AAM3104Q10 |
|
|
All Rights Reserved © IC-ON-LINE 2003 - 2022 |
[Add Bookmark] [Contact Us] [Link exchange] [Privacy policy] |
Mirror Sites : [www.datasheet.hk]
[www.maxim4u.com] [www.ic-on-line.cn]
[www.ic-on-line.com] [www.ic-on-line.net]
[www.alldatasheet.com.cn]
[www.gdcy.com]
[www.gdcy.net] |